In 2021, it is still a year of DTF Printer anomalies. Global customers use a wide group, there is still a very huge newcomer. Many novice customers are the first time to contact DTF Printer, will not be used, or during use, some details have not been noticed, and they will encounter the machine that can not work properly. Then we should avoid these problems in the usual use of us, or how to solve problems. Below, we will introduce a detailed introduction.
1 The DTF Printer car did not return to the original position
Sometimes the customer will find that the print cars will not return to the original during the boot process or when the print command is sent. This problem can be divided into the following three categories: a. After the power source, the platform is still outside. Waiting for a while, after booting; b. When sending print commands, the platform is still outside; c. Software settings errors.
There are two cases of AB because the DTF Printer platform is not caused in the initial position. Therefore, you must pay attention to the platform position when you turn off the plane. And this case, you need to read the instructions carefully or ask the post-sales master, step by step to set the correct print option in the relevant RIP software.
2 The DTF Printer printing truck hits the left stop
Sometimes, the printer suddenly hit the left stop during the startup process and issued a huge noise. What is the reason for this problem? This is because the white ink printer is not clean enough, and the surface of the grating bar must be kept clean. If the raster case sensor is also dirty, it is also possible to make wiping to ensure its clean level.
3 The DTF Printer printing the motor speed is very slow.
DTF Printer’s print carts are slow in starting speed during startup or printing. This is because the long-term print rail will slightly wear, this solution is to give the printed traveler rail. This will reply normally.
4 The ink box is a bright red light
The ink cartridge is bright red light during printing. The previous machine may only be bright red, and the current machine will make a bright alarm sound. This is the lack of ink alarm system. When there is no ink in the ink cartridge of the DTF Printer, it will automatically perform an early warning, reminding the operator to need to add ink. Does the ink are full? How much ink is appropriate? We will answer you in the next question.
5 Is the ink to be full?
There are many customers who have not contacted the DTF Printer class, and after receiving the machine, they have an urgent plum. I don’t carefully listen to the training of after-sales and see the manual and operational video we are randomly provided. If you receive the machine, you can also add the number of additions to the ink, it is considered to be full. As a result, DTF Printer runs a problem, it will blame our machine quality. We are very responsive to tell you: it is because your approach is wrong, so it can’t be used normally.
The best way to solve this problem is: Don’t complete it in DTF Printer plus, add a half because the working principle of the ink cartridge is different from the filler ink cartridge. If the ink is very full, the ink can not be supplied to the small ink cartridge due to the problem of air pressure, resulting in printing ink; on the other hand, it is very easy to appear ink during printing. Finally, pay attention to the color of the plus ink, don’t add the wrong ink bottle.
6 Print interrupt
During the DTF Printer printing process, the task is not finished, the printing carrier is suddenly returned, and there is no error on the button on the keyboard. This must check if there is a problem with the following: a. Check if the USB cable is loose or the connector is not cautious; b. After the control panel uninstall the printer driver, restart the computer, reinstall; c. If The above is not, check if the C disk is insufficient; d. Check if the input voltage is stable; E. Try other computers.
7 Print pattern is bias
Sometimes, DTF Printer uses it on the previous day. The result suddenly found that the print pattern is biased. Is it broken? Make a print test strip before running it properly, see if it is lacking. If you find that the color lines of the test strips are severe, try to make nozzle cleaning, then test the test strips, make sure each color is good.
Note: Many people will ignore the print test strips, so we must develop a good habit of printing the test strips before booting, and can only ensure that the test results are normal, or you will cause color difference.
8 The print pattern has left and right heavy shadows
During the DTF Printer printing process, what is the reason why the pattern has left and right, what is this? Such cases can be used to clean the raw rings to clean up with a clean cotton or paper towel. The raster strip position is in the upper end of the print cart rail, which is a transparent strip.
Note: Some operators do not pay attention to maintaining cleaning machines during the DTF Printer process. After a long time, the operating environment will be very dirty, and the print body platform is a waste ink. The raster bar is a precision component. If there is dust or even ink, the inductor on the rear of the print is unable to appear, thereby printing the phenomenon of printing. In the process of using the printer, it is necessary to ensure the cleaning of the printer’s surface.
9 The color does not come, and the cleaning can not solve the problem.
The front day of the machine’s nozzle checks is normal and can run. There is no color today, and the nozzle is cleaned. This type is much more waste in ink, which is too much waste ink, as long as you care, then clean your printhead, and then clean it. Finally, remember to re-print the test strip, the test strip is normal after it is normal.
When there is no ink in the ink cartridge of the DTF Printer, it will automatically perform an early warning, reminding the operator to need to add ink. The best way to solve this problem is: Don’t complete it in DTF Printer plus, add a half because the working principle of the ink cartridge is different from the filler ink cartridge. If the ink is very full, the ink can not be supplied to the small ink cartridge due to the problem of air pressure, resulting in printing ink; on the other hand, it is very easy to appear ink during printing. Pay attention to the color of the plus ink, don’t add the wrong ink bottle.
In the process of using the printer, it is necessary to ensure the cleaning of the printer’s surface.
Finally, we have a series of training whenever you have purchased under the Sublistar brand. We will randomly machine attach the household manual and operational video. If these are not enough, we also have technical guidance and arrange a suitable time for both parties, it is possible to perform remote operation guidance.
